Parallel Gripper

New Zaytran Parallel Gripper GPL 400 SM 32250
Paypal

US $2,300.00

PHD Parallel Pneumatic Gripper GRC162 2 5001 GRC
Paypal

US $1,699.99

SCHUNK 2 FINGER PARALLEL GRIPPER PGN200 2S PGN200 2AS
Paypal

US $1,500.00

SCHUNK 2 FINGER PARALLEL GRIPPER TYPE PUG 100 PUG100
Paypal

US $1,500.00

Robohand Parallel 2 Jaw Gripper Wide Body Series RPW 500 2
Paypal

US $1,300.00

Destaco Robohand Cylindrical Parallel Gripper RIP 163 C
Paypal

US $1,299.99

Parallel Gripper

Adawall With Construction Adhesive

Adawall Construction Adhesive

Description of Product:

Adawall Costruction Adhesive is a single component, water based gap filling, adhesive.

Fields of Application:

Quick and permanent fixing of a wide range of commonly used building and decorative materials including:
? Stair nosings.
? Plasterboard.
? Plywood.
? Insulation boards.
? Timber battens.
? Sheet timber flooring systems.
? Skirtings and architraves.
? Carpet gripper rods.
? Ceiling roses
? Coving

Features and Benefits:

? Outperforms most solvated and polyurethane adhesives
? Solvent free - low odour
? Easy to use and apply.
? Good adhesion to a wide range of building materials.
? Instant Grab.
? Eliminates the need for screwing and nailing.
? Priming not normally required.
? Excellent bond strength.
? Gap-filling.

Technical Data/Typical Properties:

Service Temperature Limits -6°C to 60°C Application Temperature Limits +5°C to +25°C Cure Time 2 - 7 days depending on type

Application Procedure

Preparation of Substrate:

Surfaces must be sound, dry, clean and free of any grease, oil and loose, flaky or weak material. This can be achieved by wire brushing if necessary.In the case of rendered or plastered surfaces no efflorescence should be evident. All nibs and other protrusions should be removed.

Priming:

Under normal circumstances this is not required. However, for porous, fibrous or very dusty surfaces recommended that a coat of primer is applied,please consult the supplier

Application:

Cut the plastic nozzle to the size of the bead required at a 450 angle. Insert the cartridge into a mastic gun squeeze the trigger to start the flow of adhesive. Apply a continuous bead of approximately 2mm to 6mm diameter onto the fixture being bonded. Actual bead size will depend on fixture and substrate. Under normal circumstances the bead should not be applied to the substrate. However, under certain conditions, for example when a fixture is applied to a timber framed backing, the application of adhesive to the substrate can facilitate alignment.Apply the fixture to the substrate as described below.

Wallboards:

Apply a continuous 6mm bead to the back of the board around the perimeter and then lengthways at 200mm centres. Immediately slide the board into
position under uniform pressure. A firm bond will be achieved in about 1 hour, but it may be necessary to provide temporary support, e.g. panel pins,to prevent slipping of the board whilst the adhesive sets.When fixing wallboards to battens, these should be fixed vertically at 400mm centres with horizontal battens top and bottom. Adhesive beads should be applied to the back of the board in positions corresponding to the positions of the battens.Alternatively, the adhesive may be applied to the battens and the wallboards pressed firmly into place immediately.When boards are warped or the wall surfaces are uneven apply Adawall Construction Adhesive as already described and then firmly press to the wall surface or battens - pull the board away immediately. Check that some adhesive has been transferred from the board
to the substrate in all cases - if not apply extra adhesive and repeat. Leave the board removed for approximately 10 to 15 minutes and then press back
into position and temporarily support if necessary.

Battens:

Apply the adhesive to the batten or to the wall. Press into position - if necessary provide temporarily support. Alternatively, when necessary use the partial transfer method described in the section above for warped and uneven surfaces.

Skirtings and Architraves:

For wider timber members, such as skirtings and architraves, apply parallel beads to the reverse side, approximately 25 mm in from the outer edges.
As appropriate, fix either directly or by the partial transfer method.

Coverage:

A standard cartridge will give approximately 42 metres of 3mm diameter bead ( or 11 metres of 6mm diameter bead).

Cleaning:

Clean all equipment immediately after use with water.

Packaging:

Adawall Construction Adhesive is supplied in 310ml cartridges equipped with nozzles.

Storage:

Store in dry cool conditions away from foodstuffs.

Shelf Life:

Up to one year when stored as recommended.

Health and Safety:

*For full information on Health and Safety matters regarding this product the relevant Health and Safety Data Sheet should be consulted.
The following general comments apply to all products. As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth,skin and foodstuffs, (which may also be tainted with vapour until the product is fully cured and dried). Treat splashes to eyes and skin immediately. If accidentally
ingested, seek medical attention. Keep away from children and animals. Reseal containers after use.

Disclaimer:

This information and all further technical advice is based on ourpresent knowledge and experience. However, it implies no liability or other legal responsibility on our part, including with regard to existing third party intellectual property rights, especially patent rights. In particular, no warranty, whether express or implied, or
guarantee of product properties in the legal sense is intended or implied. We reserve the right to make any changes according to technological progress or further developments. The customer is not released from the obligation to conduct careful inspection and testing of incoming goods. Performance of the product described herein should be verified by testing, which should be carried out only by qualified experts in the sole
responsibility of a customer. Reference to trade names used by other companies is neither a recommendation, nor does it imply that similar products could not be used.

About the Author

I am Adi Day and I work for WT Burdens.